Quick-Check-TCell Tower Cable Tension Meter with Bluetooth Output
The Quick Check-T tension meter with Bluetooth output is designed for precise tension measurement of tower guy cables. The included mobile app produces comprehensive reports of tension readings with GPS location, date, and time which can be easily exported once the job has been completed.
The QC-T can be placed on a cable, measure its tension, and removed in under three seconds! There are no complex lookup tables or conversion charts required. The operator can quickly select from 20 different wire sizes and types stored in QC-T's memory. The Check-Tensioning mode graphically displays the current and target tensions for an extremely quick setting of line tension. Even the infrequent battery changes are quick.
The QC-T is used in many industries to ensure proper tensioning. Typical applications include tower and stack guy wires, zip lines, pretensioned cable barriers, bridges, elevators, winch rope, overhead electric transit wires, fall arrest systems, hll horizontal life lines, aircraft cables and utilities.
Features
Supplied with NIST Traceable Calibration Report
Bluetooth Output for Comprehesive Site Report Generation View Sample
Multi-wire single sheave
Automatic target tension calculations
Ability to capture pre and post tension readings
2 year warranty
Specifications
Capacity
10,000 lb/45 kN/4500 kg
Accuracy
±3% instrument capacity
Calibrations
Up to 20 can be stored independently
Operating Temperature
-4°F to 158°F (-20°C to 70°C)
Units of Measure
lbf, kgf & Newtons
Size
0 x 23 x 3” (25 x 59 x 8 cm)
Weight
about 11 lb (5kg)
Display
Dot-graphic LCD display supports full text
Environmental Protection
Suitable for continued outdoor use
Protection
Hard polymer storage case included
Power
2 x AA batteries with 120+ hours life (backlight off)
2 Ranges
2000 lb / 10 kN / 1000 kg - PN AWT05-508112
10000 lb / 45 kN / 4500 kg - PN AWT05-508111
Cables Sizes 3/16" - 1" (5mm - 25mm) (OD)
The Quick-Check Red Cable Tension Meter measures line tension in guy wires, zip lines, guardrail cable, guyed mast towers and overhead lines. It installs, measures and removes in seconds. The Quick-Check features a precision loadcell for highly accurate measurements that do not require lookup or correction tables.
The Quick-Check Red can be placed on a cable, measure its tension, and removed in under three seconds! There are no complex lookup tables, no conversion charts. The operator can quickly select from 20 different wire sizes and types stored in the Quick-Check's memory. The Check-Tensioning mode graphically displays the current and target tensions for extremely quick setting of line tension. Even the infrequent battery changes are quick.
The Quick-Check Red is used in many industries to ensure proper line tension. Common applications include tower and stack guy wires, zip lines, pretensioned cable barriers, bridges, elevators, winch rope, overhead electric transit wires, fall arrest systems, aircraft cables and utilities.
Features
- Includes NIST-Traceable Calibration Certificate
- 2 Year Warranty
- Stores calibrations for up to 20 unique wire sizes and types up to 1 inch max. (25 mm)
- CE Certified
- Portable and rugged – designed for outdoor use
- Telescoping handle engages meter quickly with minimal effort
- Uses stanadrd AA Batteries for up to 120 hours of use
- User-selected units of measure of Lbf, Kgf or Newtons
Calibration Suggested wire calibrations:
Calibrate each cable diameter installed with the most appropriate sheaves. If two cable types are used of the same diameter (e.g. ½” 7x7 and ½” 6x19), calibrate each type independently if accuracy is critical.
Recalibration: At user discretion. Commonly 24 months but should be more frequently with heavy use. Factory recalibration conducted typically in 2-4 days.
Custom Calibration Available
The Quick-Check can be calibrated with a customer supplied sample if none of the factory calibrated materials are suitable. In this case a 10 ft. sample must be supplied (non-returnable).
Specifications
Capacity
AWT05-508112 - 2000 lb / 10 kN / 1000 kg
AWT05-508111 - 10000 lb / 45 kN / 4500 kg
Resolution (Selectable)
AWT05-508112 Low 10lb/5Kg - Med 5lb/2Kg - High 2lb/1Kg
AWT05-508111 Low 50lb/20Kg - Med 20lb/10Kg - High 10lb/5Kg
*Default Setting is Medium
Wire sizes
3/16 inch through 1 inch (4.75 - 25mm)
Accuracy
±3% instrument capacity
Number of calibrations
Up to 20 can be stored independently
Operating Temperature
-4°F to 158°F (-20°C to 70°C)
Loading error
Cable elongation of only 0.08 inch (2mm)
Display
Informative Display: Shows Unit, Wire Type, Sheave & Battery;
Date and Time
Included
Calibration Reminder
Included (set by factory)
Backlight
Included (configurable intensity and timer)
Power
AA batteries x2
Battery Life
10 Hz = over 250 hours continuous
100Hz = over 100 hours continuous
*Tested with blacklight off
AZT (Automatic Zero Tracking) & Filtering
Configurable AZT and Filtering
Carrying Case
Included
RS-232 Port
4-Pin Lemo RS-232 output
Sheave range
Sheave accommodates rated cable size and 1/2" smaller. Sheaves are not compatible with larger wire sizes - order additional sheaves for wire sizes.
Units Of Measure
pound-force, kilogram force, Newtons
Environment protection
Suitable for continued outdoor use
Dimensions
10 x 23 x 3 inch (25 x 59 x 8 cm)
Weight
Approx 11 lb (5 kg)
Shipping Weight
30 lbs (14 kg)
Shipping Dimensions
28 x 16 x 7 inches (71 x 41 x 18 cm) with carrying case
Warranty
2 Years
What Size Sheaves should be Selected?
Three sheave sizes are available. For most applications one sheave set for the entire assortment of wire they tension will be sufficient. If you need to check tension in both 3/16" and 3/4" rope, then they should order two sheave sets. The operator must use the appropriate sheave set for the wire size and calibration stored. Changing sheaves sets takes about two minutes with the included wrench. Calibration
The Quick-Check needs to be calibrated in advance for each wire diameter / wire construction you will be measuring. 1 calibration is included at no charge, each additional calibration is $120.
When listing cables you must provide the diameter & construction, for example;
Cable 1: 1/2", 1x7
Cable 2: 3/4", 1x19
CTM
Cable Tension Meter - DISCONTINUED, REPLACED BY CTM2
The Check-Line Type CTM Digital Cable Tension Meter quickly measures tension in cable guardrails, guy wires and overhead lines. It installs, measures and removes in seconds. The digital loadcell is highly accurate and requires no lookup or correction tables.
The Fastest Cable Tension Meter
The CTM can be placed on a cable, measure its tension, and removed in under five seconds! There are no complex lookup tables, no conversion charts. The operator can quickly select from 15 different cable sizes and types stored in the CTM's memory. The Check-Tensioning mode graphically displays the current and target tensions for extremely quick setting of line tension. Even the infrequent battery changes are quick.
Broad Application
The CTM can be employed in many industries to ensure proper tensioning. Typical applications include tower and stack guy wires, pretensioned cable barriers, bridges, elevators, winch rope, prestressed concrete, fall arrest systems, aircraft cables and utilities.
Features
- Includes NIST-Traceable Calibration Certificate
- 2 Year Warranty
- Stores calibrations for up to 15 unique wire sizes and types up to 1 inch max. (25 mm)
- CE Certified
- Portable and rugged – designed for outdoor use
- Telescoping handle engages meter quickly with minimal effort
Specifications
Capacity
CTM-2000 - 2000 lb / 10 kN / 1000 kg
CTM-10000 - 10000 lb / 45 kN / 4500 kg
Resolution (Selectable)
CTM-2000 Low 10lb - Med 4lb - High 2lb
CTM-10000 Low 50lb - Med 4lb - High 2lb
*Default Setting is Medium
Wire sizes
3/16 inch through 1 inch (4.75 - 25mm)
Accuracy
±3% instrument capacity
Number of calibrations
Up to 15 can be stored independently
Operating Temperature
-4°F to 140°F (-20°C to 60°C)
Loading error
Cable elongation of only 0.08 inch (2mm)
Display
Dot-graphic LCD display
supports full text and 1 inch high digits
Sheave range
Sheave accommodates rated cable size and 1/2" smaller. Sheaves are not compatible with larger wire sizes - order additional sheaves for wire sizes.
Units Of Measure
pound-force, kilogram force, Newtons
Environment protection
Suitable for continued outdoor use
Dimensions
10 x 23 x 3 inch (25 x 59 x 8 cm)
Weight
Approx 11 lb (5 kg)
Shipping Weight
25lbs (12 kg)
Shipping Dimensions
29 x 19 x 9 inch with case
Warranty
2 Years
CTM-RENT
Quick-Check Cable Tension Meter Rental
Quick-Check - AWT05-508111 / AWT05-508251
Capacity: 10000 lb / 45 kN / 4500 kg
Cable Diameter: 1/4" up to 1" (6.35mm - 25mm) (OD)
We offer a CTM2-10000 Cable Tension Meter with type "P" Sheaves and type "T" Sheaves for rent, it is pre-programmed with the following common tower calibrations:
Rental pricing: $1000 for the first week, $100 for each additional business day, $2000 security deposit, refunded after return to Electromatic in "as-received" condition. Please call 516-295-4300 or email info@checkline.com for more details. CALL 1-800-645-4330 FOR CURRENT AVAILABILITY,
Please view the CTM webpage for complete product specifications. Supplied in foam-fitted carry/transport case and fitted with Sheave Set Code S for 1/4" to 3/4" wire rope as well as Sheave Set Code T for 7/8" and 1" wire rope. NIST-Traceable Calibration Certifications supplied for all programmed calibrations
QB-10000
Capacity: 10000 lb / 45 kN / 4500 kg
Calibration: Calibrated for 1⁄2", 9⁄16" and 5⁄8" wire rope (8x19) additional calibrations are optional
The new QB-10000 Tension Meter provides a quick and easy way to accurately measure and display all of the elevator traction cable tensions in a set while the tension on a single cable is being adjusted. This makes it extremely easy to balance the tensions of up to 16 elevator cables or any other multiple-line array of tension cables, such as tower and stack guy wires, crane rigging sets and platform lifts, etc. The digital display also shows the average tension of the set as well as the total tensile load.
The QB-10000 installs easily, measures cable tension up to 10,000 lbs directly, stores readings and is removed from the cable in seconds. No lookup or reference to correction or conversion charts is required. Writing down measurements for comparison purposes is also not required.
Balancing the tensions on a set of cables takes minutes instead of hours and can be done by a single person, working alone, instead of two or three.
Rope Tension Meter รุ่น EZGH (LONROY) 