เครื่องทดสอบแรงบิด CD Series (JAPAN)
ใช้งานเพื่อบันทึกเกณฑ์การผ่าน/ไม่ผ่าน 5 ช่องสัญญาณ และเปิดใช้งานเพื่อเปลี่ยนการตั้งค่าโดยเปลี่ยนช่องสัญญาณ แม้ว่าข้อกำหนดที่เข้มงวดจะเปลี่ยนไปก็ตาม ความทนทานสูงต่อแรงบิดสูงที่โหลดโดยไม่คาดคิด (ทนทานกว่ารุ่นทั่วไปถึงสามเท่า) นอกจากนี้ อะแดปเตอร์ที่ต่ออยู่จะไม่แยกชิ้นส่วนของข้อต่อเนื่องจากการกรอกลับมากเกินไป จึงสามารถใช้งานและจัดการได้ตามปกติ
ดาวน์โหลด
CD-100M/10M
Suitable for daily inspection of electric screw driver
Using convensional joint (SJ joint (PAT))
Enable to save 5 channels of pass/fail judgement criterion, and enable to change settings by switch channels even if the tightening term changes.
High durability against high torque loaded unexpectedly. (triple the durability of conventional model).
Also, the attached adapter does not disassemble the joint due to excessive rewinding.It can be used and managed in a conventional way.
The best for everyday check of an electric driver
- Everyday check of an electric driver can be performed.
- Since various informationis displayed on a display board, it is very intelligible.
- The change of a measurement unit can be performed.
- Memory data is 800 affairs.
- Real-time output, every about 1/180 seconds
- The taking-in software of data can download from a homepage.
- Show “Measurement mode”, “Measurement unit”, “maximum, minimum, average”
- Switchable measurement unit
- Enable to save 5 sets of settings such as upper limit and lower limit
- 800 items of memory data
- Real-time output About every 1/180 seconds
- Data acquisition software can be downloaded for free
Yes-No Decision Conditions, Etc. Can Save Five Channels
A channel is only changed even if bolting conditions change.
It is not necessary to reset up a maximum value and a minimum value one by one like former.
.png)
| Specification |
CD-100M |
CD-10M |
| Measuring Range |
– 0.10 ~ 10.00 Nm
-1.0 ~ 100.0 kgf.cm
– 1.0 ~ 90 lbf.in
|
– 0.010 ~ 1.000 Nm
-0.10 ~ 10.00 kgf.cm
– 0.10 ~ 9.000 lbf.in
|
| Accuracy |
±0.5% (199 digit or less ± 1 digit) |
| Display |
The 3.5 figures digital display of LCD |
| The Measurement Direction |
CW-CCW (right and left) |
| Zero Return By One Touch |
Return to zero by pressing clear button |
| Measurement Mode |
Track, P-P(peak to peak), P-D(peak-down), C(real-time output) |
| High and Low Limits Judging Function |
High and low valuee are measurement within the limits, and can be set up |
| Real-Time Output |
Load torque value is outputted every about 1/180 second |
| The Maximum, The Minimum, and The Average Value Display |
The maximum, the minimum, average value |
| Data Output |
ASCH format (baud rate 19200) |
| Auto Power Save |
10 minutes no use, automatically switch off |
| Power Supply |
Ni-Cd chargeable battery 1.2V x 5 cells 700mAh |
| Charging Time |
About 3 hours |
| Continuous Working Time |
About 12 Hours |
| Clearence |
It is a display clearance in set-up time (0.1- 0.3 sec) |
| Socket Size |
20mm / 9.5mm |
| Dimension / Weight |
W: 160 x D: 125 x H: 55 / About 1kg |
| Recommend Buffer Accessories |
Measuring Joint SJ-50,SJ-10K |
Measuring Joint SJ-10 |
| AC/DC adaptor |
| Exclusive receipt case |
| An inspection report, a proofreading certificate, a traceability system figure |
เครื่องทดสอบแรงบิด DI-4B-25 (JAPAN) 